【摘要】：針對水力機械水力暫態過程中非定常流動的動邊界問題,基于浸入邊界法的建模思想,將剛體運動對流場的影響以附加體力的形式加入Navier-Stokes方程,建立了活動導葉連續運動和流體相互作用的數學模型.采用直接分步投影方法求解基于浸入邊界法的耦合系統方程,其中固體邊界離散點的作用力密度通過強制滿足流固邊界的無滑移條件導出,并通過δ光滑函數轉換到流場的歐拉網格點上,實現對速度場的二次修正.通過數值模擬活動導葉連續運動下葉道內復雜湍流流動,獲取活動導葉連續開、關過程中渦量等流動參量的時變特性和作用于轉輪上的水力載荷特性.計算結果有助于水力機械暫態過程和機組穩定性控制策略的優化設計.
[Abstract]:Aiming at the dynamic boundary problem of unstable flow in hydraulic transient process of hydraulic machinery, based on the modeling idea of immersion boundary method, the influence of rigid body motion on flow field is added to Navier-Stokes equation in the form of additional physical force. The mathematical model of continuous motion and fluid interaction of moving guide vane is established. The direct step projection method is used to solve the coupled system equation based on the immersion boundary method, in which the force density of the discrete point of the solid boundary is derived by forcibly satisfying the non-slip condition of the fluid-solid boundary. The second correction of the velocity field is realized by converting the 未 smooth function to the Euler grid point of the flow field. By numerical simulation of the complex turbulent flow in the vane under the continuous motion of the movable guide vane, the time-varying characteristics of the flow parameters such as the continuous opening and closing of the movable guide vane and the hydraulic load characteristics acting on the runner are obtained. The calculation results are helpful to the optimal design of transient process and stability control strategy of hydraulic machinery.
【作者單位】： 昆明理工大學工程力學系;
【基金】：國家自然科學基金資助項目(11262008,51479085) 霍英東青年基金資助項目(141120)
【分類號】：TV136.1

【相似文獻】

相關期刊論文 前3條

1 朱艷;;大型水輪機活動導葉裝焊工藝研究[J];黑龍江科技信息;2004年07期

2 高忠信;唐澍;梁賀志;;水輪機固定導葉和活動導葉后的卡門渦頻率研究[J];水動力學研究與進展(A輯);2005年06期

3 ;[J];;年期

相關會議論文 前4條

1 王希靖;李鶴岐;張瑞華;;水輪機活動導葉表面修復時的隨形磨削[A];第九次全國焊接會議論文集（第2冊）[C];1999年

2 楊波;;大朝山水電站一號機組活動導葉上浮的處理[A];2010年云南電力技術論壇論文集（文摘部分）[C];2010年

3 王希靖;李鶴岐;張瑞華;;水輪機活動導葉修復時的自動變位機構及控制系統[A];第十次全國焊接會議論文集（第2冊）[C];2001年

4 羅興，

本文編號：2494479